- Melting point:
- -94 °C(lit.)
- Boiling point:
- 56 °C760 mm Hg(lit.)
- 0.791 g/mL at 25 °C(lit.)
- vapor density
- 2 (vs air)
- vapor pressure
- 184 mm Hg ( 20 °C)
- refractive index
- 3326 | ACETONE
- Flash point:
- 1 °F
- storage temp.
- Store at RT.
- Miscible with water and with ethanol (96 per cent).
- 19.3(at 25℃)
- Colorless, invisible vapor
- Specific Gravity
- 0.79 (25/25℃)
- Characteristic pungent odor detectable at 33 to 700 ppm (mean = 130 ppm)
- 5-6 (395g/l, H2O, 20°C)
- Relative polarity
- explosive limit
- Water Solubility
- JECFA Number
- Henry's Law Constant
- 2.27 at 14.9 °C, 3.03 at 25 °C, 7.69 at 35.1 °C, 11.76 at 44.9 °C (Betterton, 1991)
- Exposure limits
- TLV-TWA 1780 mg/m3 (750 ppm), STEL 2375 mg/m3 (ACGIH); 10 h–TWA 590 mg/m3 (250 ppm); IDLH 20,000 ppm (NIOSH).
- CAS DataBase Reference
- 67-64-1(CAS DataBase Reference)
- NIST Chemistry Reference
- EPA Substance Registry System
- Risk and Safety Statements
|RIDADR||UN 1090 3/PG 2
|Autoignition Temperature||465 °C|
|Toxicity||LD50 in rats: 10.7 ml/kg orally (Smyth)|
|Health||1||Exposure would cause irritation with only minor residual injury (e.g. acetone, sodium bromate, potassium chloride)|
|Flammability||3||Liquids and solids (including finely divided suspended solids) that can be ignited under almost all ambient temperature conditions . Liquids having a flash point below 22.8 °C (73 °F) and having a boiling point at or above 37.8 °C (100 °F) or having a flash point between 22.8 and 37.8 °C (73 and 100 °F). (e.g. gasoline, acetone)|
|Instability||0||Normally stable, even under fire exposure conditions, and is not reactive with water (e.g. helium,N2)|
中国福彩网论坛 www.hoaemj.tw (NFPA, 2010)
Acetone Chemical Properties,Uses,Production
IntroductionAcetone (also known as propanone, dimethyl ketone, 2-propanone, propan-2-one and β-ketopropane) is the simplest representative of the group of chemical compounds known as ketones. It is a colorless, volatile, flammable liquid.
Acetone is miscible with water and serves as an important laboratory solvent for cleaning purposes. Acetone is a highly effective solvent for many organic compounds such as Methanol, ethanol, ether, chloroform, pyridine, etc., and is the active ingredient in nail polish remover. It is also used to make various plastics, fibers, drugs, and other chemicals.
Acetone exists in nature in the Free State. In the plants, it mainly exists in essential oils, such as tea oil, rosin essential oil, citrus oil, etc.; human urine and blood and animal urine, marine animal tissue and body fluids contain a small amount of acetone.
- An important organic raw material in the chemical, artificial fiber, medicine, paint, plastics, organic glass, cosmetics and other industries; an excellent organic solvent that dissolves many organic products such as resin, cellulose acetate, acetylene and so on.
- An important raw material for the synthesis of ketene, acetic anhydride, iodoform, polyisoprene rubber, methacrylic acid, methyl ester, chloroform, and epoxy resins.
- The acetone cyanohydrin obtained from the reaction of acetone with hydrocyanic acid is the raw material of methacrylic resin (perspex).
- A raw material in the production of epoxy resin intermediate bisphenol A.
- In pharmaceuticals, acetone is used as extractants for a variety of vitamins and hormones in addition to vitamin C, and dewaxing solvents for petroleum refining.
- A raw material for nail polish remover in cosmetics
- One of the raw materials for synthesizing pyrethroids in pesticide industry
- Acetone is often used to wipe the black ink above the copper tube in the precision copper tube industry.
ProductionIn 1913, the United Kingdom developed a method for fermenting cereals to produce acetone and butanol. In 1920, the dehydrogenation of isopropanol (synthesized by hydration of propylene) appeared. From 1953 to 1955, the United States Hercules and the British Distilling Company jointly developed the cumene process method, thereafter, Japan, the United Kingdom, and the Netherlands also developed other methods. Now, Most of the worldwide industrial production of acetone (and phenol) is based on the cumene process, which uses benzene and propylene as raw materials, via cumene intermediates, then oxidized, hydrolyzed to produce acetone and co-produced phenol.
Acetone is mainly used as an organic solvent and methyl methacrylate (the main raw material for organic glass).In the United States and Western Europe, the two accounts for 70% of the total consumption. It is used for bisphenol A, accounting for 10% to 15%, and the others 15% % to 20%.
Health EffectsSummary: Acetone is mainly responsible for the inhibition and anesthesia of the central nervous system and exposure to high concentrations may cause liver, kidney, and pancreas impair to particular people. Because of its low toxicity, rapid metabolism and detoxification, acute poisoning under production conditions is rare. In case acute poisoning happens, symptoms of vomiting, shortness of breath, paralysis, and even coma can occur. After oral administration, burning sensation in the lips and throat may occur after hours of incubation, such as dry mouth, vomiting, drowsiness, acidity and ketosis, and even temporary disturbance of consciousness. The long-term damage of acetone to the human body is manifested as irritation to the eyes such as tearing, photophobia and infiltration of the corneal epithelium, as well as dizziness, burning sensation, throat irritation, and coughing.
Metabolism in the body: After being absorbed by the lungs, gastrointestinal tract, and skin, acetone is easily absorbed into the bloodstream due to its high water solubility and is rapidly distributed throughout the body. The excretion depends on the dose. When the dose is large, the main tract is mainly through the lungs and kidneys, and a very small amount is discharged through the skin. When the dose is small, most of them are oxidized into carbon dioxide. The biological half-life of acetone in blood is 5.3 h for rats, 11 h for dogs, and 3 h for humans. The metabolites of acetone in the human body are mostly a tricarboxylic acid cycle intermediate that is decomposed to acetoacetate and converted to glycogen.
DescriptionAcetone is a flammable, colorless liquid with a pleasant odor. It is used widely as an organic solvent and in the chemical industry. It is the simplest ketone, which also goes by the name dimethyl ketone (DMK). Acetone was originally referred to as pyroacetic spirit because it was obtained from the destructive distillation of acetates and acetic acid.
Chemical PropertiesA clear liquid with characteristic aromatic odor; pungent, somewhat sweet taste. It is used as a flavor enhancer, flavoring agent or adjuvant solvent, or vehicle washing or surface removal agent. Its quick miscibility with water, alcohol, ether, chloroform and most volatile oils makes acetone a valuable solvent and extractant
Chemical PropertiesAcetone is a colorless volatile, flammable, transparent liquid, with a sweetish odor and pungent sweetish taste.
Chemical PropertiesAcetone, CH3COCH3, also known as 2-propanone and dimethylketone, is a colorless, volatile,flammable liquid that boils at 56°C (133 OF). It is misciblewith water and is oftenused as a solventin the manufacture of lacquers and paints.
Chemical PropertiesAcetone is a highly flammable, colorless liquid with a sweet, mint-like odor
Physical propertiesClear, colorless, liquid with a sweet, fragrant odor. Sweetish taste. Odor threshold concentrations ranged from 42 ppmv (Nagata and Takeuchi, 1990) to 100 ppmv (Leonardos et al., 1969). Experimentally determined detection and recognition odor threshold concentrations were 48 mg/m3 (20 ppmv) and 78 mg/m3 (33 ppmv), respectively (Hellman and Small, 1974).
OccurrenceReported found in apple, pear, grape, pineapple, strawberry, raspberry, tomato, black currant, citrus, onion and potato; also reported found in cocoa leaves, in Mexican goosefoot and in the oils of coriander and lavender. In trace amounts it has been reportedly identified in the oil of bitter orange, in distilled wine and in coffee aroma
HistoryThe traditional method of producing acetone in the 19th century and the beginning of the 20th century was to distill acetates, particularly calcium acetate, Ca(C2H3O2)2.
Weizmann discovered a process to produce butyl alcohol and acetone from the bacterium Clostridium acetobutylicum in 1914. With England’s urgent demand for acetone, Winston Churchill (1874–1965) enlisted Weizmann to develop the Weizmann process for acetone production on an industrial scale. Fermentation and distillation techniques for acetone production were replaced starting in the 1950s with the cumene oxidation process . In this process, cumene is oxidized to cumene hydroperoxide, which is then decomposed using acid to acetone and phenol. This is the primary method used to produce phenol, and acetone is produced as a co-product in the process, with a yield of about 0.6:1 of acetone to phenol.
UsesAcetone is used in the manufacture of a largenumber of compounds, such as acetic acid,chloroform, mesityl oxide, and MIBK; in themanufacture of rayon, photographic films,and explosives; as a common solvent; inpaint and varnish removers; and for purifyingparaffins.
UsesAcetone is used in the chemical industry in numerous applications. The primary use of acetone is to produce acetone cyanohydrin, which is then used in the production of methyl methacrylate (MMA). Another use of acetone in the chemical industry is for bisphenol A (BPA). BPA results form the condensation reaction of acetone and phenol in the presence of an appropriate catalyst. BPA is used in polycarbonate plastics, polyurethanes, and epoxy resins. Polycarbonate plastics are tough and durable and are often used as a glass substitute.
In addition to its use as a chemical feedstock and intermediate, acetone is used extensively as an organic solvent in lacquers, varnishes, pharmaceuticals, and cosmetics. Nail polish remover is one of the most common products containing acetone. Acetone is used to stabilize acetylene for transport .
Usesacetone is a solvent considered to be non-comedogenic and occasionally used in skin toners. It is primarily used in nail polish remover. It could be drying and very irritating to the skin depending on the concentration and frequency of use.
UsesAcetone′s luminesence intensity is dependent upon the solution components 1. The absorption of UV light by acetone, results in its photolysis and the production of radials 1.
UsesSuitable for HPLC, spectrophotometry, environmental testing
UsesUsed in liquid chromotography; cleaning glassware; extraction of solid waste.
UsesSolvent for fats, oils, waxes, resins, rubber, plastics, lacquers, varnishes, rubber cements. manufacture of methyl isobutyl ketone, mesityl oxide, acetic acid (ketene process), diacetone alcohol, chloroform, iodoform, bromoform, explosives, aeroplane dopes, rayon, photographic films, isoprene; storing acetylene gas (takes up about 24 times its vol of the gas); extraction of various principles from animal and plant substances; in paint and varnish removers; purifying paraffin; hardening and dehydrating tissues. Pharmaceutic aid (solvent).
DefinitionChEBI: A methyl ketone that consists of propane bearing an oxo group at C2.
Production MethodsAcetone can also be produced from isopropanol using several methods, but the main methodis by catalytic dehydrogenation.
Production MethodsAcetone is obtained by fermentation as a by-product of n-butyl alcohol manufacture, or by chemical synthesis from isopropyl alcohol; from cumene as a by-product in phenol manufacture; or from propane as a by-product of oxidation-cracking.
Aroma threshold valuesDetection: 40 to 476 ppm
General DescriptionA clear colorless liquid with a sweetish odor. Flash point 0°F. Less dense than water. Vapors are heavier than air. Used as a solvent in paint and nail polish removers.
Air & Water ReactionsHighly flammable. Water soluble.
Reactivity ProfileAcetone was reported that a mixture of Acetone and chloroform, in a residue bottle, exploded. Since addition of Acetone to chloroform in the presence of base will result in a highly exothermic reaction, Acetone is thought that a base was in the bottle [MCA Case History 1661. 1970]. Also, Nitrosyl chloride, sealed in a tube with a residue of Acetone in the presence of platinum catalyst, gave an explosive reaction [Chem. Eng. News 35(43):60. 1967]. The reaction of nitrosyl perchlorate and Acetone ignites and explodes. Explosions occur with mixtures of nitrosyl perchlorate and primary amine [Ann. Chem. 42:2031. 1909]. Reacts violently with nitric acid. Also causes exothermic reaction when in contact with aldehydes.
Health HazardINHALATION: vapor irritating to eyes and mucous membranes; acts as an anesthetic in very high concentrations. INGESTION: low order of toxicity but very irritating to mucous membranes. SKIN: prolonged excessive contact causes defatting of the skin, possibly leading to dermatitis.
Health HazardThe acute toxicity of acetone is low. Acetone is primarily a central nervous system depressant at high concentrations (greater than 12,000 ppm). Unacclimated volunteers exposed to 500 ppm acetone experienced eye and nasal irritation, but it has been reported that 1000 ppm for an 8-hour day produced no effects other than slight transient irritation to eyes, nose, and throat. Therefore there are good warning properties for those unaccustomed to working with acetone; however, frequent use of acetone seems to cause accommodation to its slight irritating properties. Acetone is practically nontoxic by ingestion. A case of a man swallowing 200 mL of acetone resulted in his becoming stuporous after 1 hour and then comatose; he regained consciousness 12 hour later. Acetone is slightly irritating to the skin, and prolonged contact may cause dermatitis. Liquid acetone produces moderate transient eye irritation. Acetone has not been found to be carcinogenic in animal tests or to have effects on reproduction or fertility.
Health HazardThe acute toxicity of acetone in testanimals was found to be low. However,in large dosages it could be moderatelytoxic. Inhalation can cause irritation ofthe eyes, nose, and throat. A shortexposure for 5 minutes to 300–500 ppmcan be slightly irritating to humans. Theodor threshold is 200–400 ppm. In highconcentrations it can produce dryness in themouth, fatigue, headache, nausea, dizziness,muscle weakness, loss of coordinatedspeech, and drowsiness. Ingestion cancause headache, dizziness, and dermatitis.Swallowing 200–250 mL can result invomiting, stupor, and coma in humans. Adose of 25 mg/kg may be fatal to dogs.
LD50 value, oral (rats): 5800 mg/k No mutagenic or carcinogenic effects havebeen reported.
Fire HazardAcetone is extremely flammable (NFPA rating = 3), and its vapor can travel a considerable distance to an ignition source and "flash back." Acetone vapor forms explosive mixtures with air at concentrations of 2 to 13% (by volume). Carbon dioxide or dry chemical extinguishers should be used for acetone fires.
Fire HazardHIGHLY FLAMMABLE: Will be easily ignited by heat, sparks or flames. Vapors may form explosive mixtures with air. Vapors may travel to source of ignition and flash back. Most vapors are heavier than air. They will spread along ground and collect in low or confined areas (sewers, basements, tanks). Vapor explosion hazard indoors, outdoors or in sewers. Runoff to sewer may create fire or explosion hazard. Containers may explode when heated. Many liquids are lighter than water.
Flammability and ExplosibilityAcetone is extremely flammable (NFPA rating = 3), and its vapor can travel a considerable distance to an ignition source and "flash back." Acetone vapor forms explosive mixtures with air at concentrations of 2 to 13% (by volume). Carbon dioxide or dry chemical extinguishers should be used for acetone fires.
Pharmaceutical ApplicationsAcetone is used as a solvent or cosolvent in topical preparations, and as an aid in wet granulation.It has also been used when formulating tablets with water-sensitive active ingredients, or to solvate poorly water-soluble binders in a wet granulation process. Acetone has also been used in the formulation of microspheres to enhance drug release.Owing to its low boiling point, acetone has been used to extract thermolabile substances from crude drugs.
Industrial usesAcetone is valuable solvent component in acrylic/nitrocellulose automotive lacquers. Acetone is the solvent of choice in film coatings operations which use vinylidene chloride-acrylonitrile copolymer formulations.Other ketones that may be used in these film coating operations include methyl isobutyl ketone, ethyl n-amyl ketone, and diisobutyl ketone.Acetone, blends of MIBK and MEK, methyl namyl ketone, ethyl n-amyl ketone, and diisobutyl ketone are all useful solvents for vinyl resin copolymers. The presence of one of the slower evaporating ketones in the solvent blend prevents quick drying, improves flow, and gives blush resistance to the coating. Acetone is also used as a resin thinner in polyester resins and as a clean up solvent for the resin reactor kettle.In solvents industry, Acetone is a component of solvent blends in urethane, nitrile rubber, and neoprene industrial adhesives.Acetone is the primary solvent in resin-type adhesives and pressure sensitive chlorinated rubber adhesives. Acetone also can be used to extract fats, oils, waxes, and resins from natural products, to dewax lubricating oils, and to extract certain essential oils.Acetone is also an important chemical intermediate in the preparation of several oxygenated solvents including the ketones, diacetone alcohol, mesityl oxide, methyl isobutyl ketone, and isophorone.
Safety ProfileModerately toxic by various routes. A skin and severe eye irritant. Human systemic effects by inhalation: changes in EEG, changes in carbohydrate metabolism, nasal effects, conjunctiva irritation, respiratory system effects, nausea and vomiting, and muscle weakness. Human systemic effects by ingestion: coma, kidney damage, and metabolic changes. Narcotic in high concentration. In industry, no injurious effects have been reported other than skin irritation resulting from its defatting action, or headache from prolonged inhalation. Experimental reproductive effects. A common air contaminant. Highly flammable liquid. Dangerous disaster hazard due to fire and explosion hazard; can react vigorously with oxidizing materials. Potentially explosive reaction with nitric acid + sulfuric acid, bromine trifluoride, nitrosyl chloride + platinum, nitrosyl perchlorate, chromyl chloride, thiotrithiazyl perchlorate, and (2,4,6-trichloro-l,3,5triazine + water). Reacts to form explosive peroxide products with 2-methyl-1,3butadiene, hydrogen peroxide, and peroxomonosulfuric acid. Ignites on contact with activated carbon, chromium trioxide, dioxygen difluoride + carbon dioxide, and potassium-tert-butoxide. Reacts violently with bromoform, chloroform + alkalies, bromine, and sulfur dichloride. Incompatible with CrO, (nitric + acetic acid), NOCl, nitryl perchlorate, permonosulfuric acid, NaOBr, (sulfuric acid + potassium dichromate), (tho-diglycol + hydrogen peroxide), trichloromelamine, air, HNO3, chloroform, and H2SO4. To fight fire, use Con, dry chemical, alcohol foam. Used in production of drugs of abuse
SafetyAcetone is considered moderately toxic, and is a skin irritant and severe eye irritant. Skin irritation has been reported due to its defatting action, and prolonged inhalation may result in headaches. Inhalation of acetone can produce systemic effects such as conjunctival irritation, respiratory system effects, nausea, and vomiting.
LD50 (mouse, oral): 3.0 g/kg
LD50 (mouse, IP): 1.297 g/kg
LD50 (rabbit, oral): 5.340 g/kg
LD50 (rabbit, skin): 0.2 g/kg
LD50 (rat, IV): 5.5 g/kg
LD50 (rat, oral): 5.8 g/kg
Chemical SynthesisBy fermentation, or by chemical synthesis from isopropanol, cumene or propane
Potential ExposureIt is used as a solvent in nail polish remover and many other chemicals. Used in the production of lubricating oils and as an intermediate in the manufacture of chloroform and of various pharmaceuticals and pesticides.
SourceNaturally occurs in blood and urine in small concentrations. Reported in cigarette smoke (1,100 ppm) and gasoline exhaust (2.3 to 14.0 ppm) (quoted, Verschueren, 1983).
Acetone occurs naturally in many plant species including cuneate Turkish savory (Satureja cuneifolia), catmint (Nepeta racemosa), Guveyoto (Origanum sipyleum), and Topukcayi shoots (Micromeria myrtifolia) at concentrations of 20, 2, 2, and 0.1, respectively (Baser et al., 1992, 1993; Ozek et al., 1992; Tumen, 1991). Acetone was also detected in Turkish calamint (Calamintha nepeta ssp. glandulosa) (Kirimer et al., 1992), pineapples, cauliflower leaves, tea leaves, West Indian lemongrass, jimsonweed, soybeans, carrots, bay leaves, hop flowers, apples, tomatoes, water mint leaves, alfalfa, pears, rice plants, white mulberries, clover-pepper, and roses (Duke, 1992). Acetone also was emitted from many forest plant species (Isidorov et al., 1985).
Acetone was detected in diesel fuel at a concentration of 22,000 μg/g (Schauer et al., 1999). Identified as an oxidative degradation product in the headspace of a used engine oil (10–30W) after 4,080 miles (Levermore et al., 2001). Acetone also was detected in automobile exhaust at concentrations ranging from 0.09 to 4.50 mg/m3 (Grimaldi et al., 1996) and in cigarette smoke at concentrations ranging from 498 to 869 mg/m3 (Euler et al., 1996).
Gas-phase tailpipe emission rates from California Phase II reformulated gasoline-powered automobiles with and without catalytic converters were 1.19 and 42 mg/km, respectively (Schauer et al., 2002).
Vereecken and Peeters (2000) reported that acetone is formed from the reaction of α-pinene and OH radicals in the atmosphere. This reaction resulted in an acetone yield of 8.5% which is consistent with available experimental data.
Schauer et al. (2001) measured organic compound emission rates for volatile organic compounds, gas-phase semi-volatile organic compounds, and particle phase organic compounds from the residential (fireplace) combustion of pine, oak, and eucalyptus. The gas-phase emission rates of acetone were 749 mg/kg of pine burned, 462 mg/kg of oak burned, and 79 mg/kg of eucalyptus burned.
Environmental FateBiological. Following a lag time of 20 to 25 h, acetone degraded in activated sludge (30 mg/L) at a rate constant ranging from 0.016 to 0.020/h (Urano and Kato, 1986). Soil bacteria can mineralize acetone to carbon dioxide (Taylor et al., 1980). Bridié et al. (1979) reported BOD and COD values of 1.85 and 1.92 g/g using filtered effluent from a biological sanitary waste treatment plant. These values were determined using a standard dilution method at 20 °C for a period of 5 d. Similarly, Heukelekian and Rand (1955) reported a 5-d BOD value of 0.85 g/g which is 38.5% of the ThOD value of 2.52 g/g. Waggy et al. (1994) reported 5, 15, and 28-d BOD values of 14, 74, and 74%, respectively. Using the BOD technique to measure biodegradation, the mean 5-d BOD value (mM BOD/mM acetone) and ThOD were 1.52 and 38.0%, respectively (Vaishnav et al., 1987).
Photolytic. Photolysis of acetone in air yields carbon monoxide and free radicals, but in isopropanol, pinacol is formed (Calvert and Pitts, 1966). Photolysis of acetone vapor with nitrogen dioxide via a mercury lamp gave peroxyacetyl nitrate as the major product with smaller quantities of methyl nitrate (Warneck and Zerbach, 1992).
Chemical/Physical. Hypochlorite ions, formed by the chlorination of water for disinfection purposes, may react with acetone to form chloroform. This reaction is expected to be significant within the pH range of 6 to 7 (Stevens et al., 1976).
storageAcetone should be stored in a cool, dry, well-ventilated place out of direct sunlight.
storageAcetone should be used only in areas free of ignition sources, and quantities greater than 1 liter should be stored in tightly sealed metal containers in areas separate from oxidizers.
ShippingUN1090 Acetone, Hazard Class: 3; Labels: 3-Flammable liquid
Purification MethodsThe commercial preparation of acetone by catalytic dehydrogenation of isopropyl alcohol gives relatively pure material. Analytical reagent quality generally contains less than 1% of organic impurities but may have up to about 1% of H2O. Dry acetone is appreciably hygroscopic. The main organic impurity in acetone is mesityl oxide, formed by aldol condensation. It can be dried with anhydrous CaSO4, K2CO3 or type 4A Linde molecular sieves, and then distilled. Silica gel and alumina, or mildly acidic or basic desiccants cause acetone to undergo the aldol condensation, so that its water content is increased by passage through these reagents. This also occurs to some extent when P2O5 or sodium amalgam is used. Anhydrous MgSO4 is an inefficient drying agent, and CaCl2 forms an addition compound. Drierite (anhydrous CaSO4) offers minimum acid and base catalysis for aldol formation and is the recommended drying agent for this solvent [Coetzee & Siao Inorg Chem 14 2 1987, Riddick & Bunger Organic Solvents Wiley-Interscience, N.Y., 3rd edn, 1970]. Acetone can be shaken with Drierite (25g/L) for several hours before it is decanted and distilled from fresh Drierite (10g/L) through an efficient column, maintaining atmospheric contact through a Drierite drying tube. The equilibrium water content is about 10-2M. Anhydrous Mg(ClO4)2 should not be used as drying agent because of the risk of EXPLOSION with acetone vapour. Organic impurities have been removed from acetone by adding 4g of AgNO3 in 30mL of water to 1L of acetone, followed by 10mL of M NaOH, shaking for 10minutes, filtering, drying with anhydrous CaSO4 and distilling [Werner Analyst (London) 58 335 1933]. Alternatively, successive small portions of KMnO4 have been added to acetone at reflux, until the violet colour persists, followed by drying and distilling. Refluxing with chromium trioxide (CrO3) has also been used. Methanol has been removed from acetone by azeotropic distillation (at 35o) with methyl bromide, and treatment with acetyl chloride. Small amounts of acetone can be purified as the NaI addition compound, by dissolving 100g of finely powdered NaI in 400g of boiling acetone, then cooling in ice and salt to -8o. Crystals of NaI.3Me2CO are filtered off and, on warming in a flask, acetone distils off readily. [This method is more convenient than the one using the bisulfite addition compound.] It has also been purified by gas chromatography on a 20% free fatty acid phthalate (on Chromosorb P) column at 100o. For efficiency of desiccants in drying acetone see Burfield and Smithers [J Org Chem 43 3966 1978]. The water content of acetone can be determined by a modified Karl Fischer titration [Koupparis & Malmstadt Anal Chem 54 1914 1982]. [Beilstein 1 IV 3180.] Rapid procedure: Dry over anhydrous CaSO4 and distil.
IncompatibilitiesMay explode when mixed with chloroform, chromic anhydride. Incompatible with acids, bases, and oxidizing materials, such as peroxides, chlorates, perchlorates, nitrates, and permanganates. Unstable peroxides formed with strong oxidizers. May accumulate static electrical charges and may cause ignition of its vapors. Dissolves most rubber, resins, and plastics.
IncompatibilitiesAcetone reacts violently with oxidizing agents, chlorinated solvents, and alkali mixtures. It reacts vigorously with sulfur dichloride, potassium t-butoxide, and hexachloromelamine. Acetone should not be used as a solvent for iodine, as it forms a volatile compound that is extremely irritating to the eyes.
Waste DisposalConsult with environmental regulatory agencies for guidance on acceptable disposal practices. Generators of waste containing this contaminant (≥100 kg/mo) must conform with EPA regulations governing storage, transportation, treatment, and waste disposal. Incineration.
Regulatory StatusIncluded in the FDA Inactive Ingredients Database (inhalation solution; oral tablets; topical preparations). Included in the Canadian List of Acceptable Non-medicinal Ingredients. Included in nonparenteral medicines licensed in the UK.
Acetone Preparation Products And Raw materials
- ACETONE ALCOHOL
- GRAMS DECOLORIZER
- GRAM STAIN NO 3
- Rcra waste number U002
- ACETONE E PESTANAL
- ACETONE 99+% FCC
- ACETONE DIST. 1 L
- ACETONE SEMICONDUCTOR GRADE MOS PURANAL
- ACETONE 'B&J BRAND' 4 L
- ACETONE SPECTRANAL, REAG. ACS
- ACETONE, REAGENTPLUS, PHENOL FREE, >=99.5%
- ACETONE, ACS, FOR UV-SPECTROSCOPY
- ACETONE, >=99.5%, A.C.S. REAGENT
- ACETONE >=99.9% HPLC GRADE (PURE-PAC
- ACETONE >=99.5% A.C.S. SPECTROPHOTOME&
- ACETONE 97+% NATURAL
- ACETONE, 4X25 ML
- ACETONE, CHROMASOLV PLUS, FOR HPLC, 99.&
- ACETONE SEMICONDUCTOR GRADE ULSI PURANAL
- ACETONE, DIST. FOR HPLC, 6X1 L
- ACETONE, >=99.5%, A.C.S. REAGENT (POLY-COATED BOTTLES)
- ACETONE CLEANING SOLUTION
- ACETONE >=99.5% A.C.S. REAGENT (POLY-&
- ACETONE EXTRA PURE, DAB, PH. FRANC.,N. F
- ACETONE, PH EUR
- ACETONE, >=99.5%, A.C.S. REAGENT (SAFETY CAN)
- ACETONE, 99.5+%, HISTOLOGICAL GRADE
- ACETONE, >=99.5%, A.C.S. SPECTROPHOTOMETRIC GRADE
- ACETONE 99.9% B&J BRAND
- ACETONE, FOR RESIDUE ANALYSIS
- ACETONE EP, BP, NF
- ACETONE, STANDARD FOR GC
- ACETONE, DIST. FOR HPLC, 4X2.5 L
- ACETONE D FOR ANALYSIS OF DIOXINES, FURA
- ACETONE >=99.5% A.C.S. REAGENT (SAFET&
- ACETONE PESTANAL
- ACETONE R. G., PE BOTTLE, REAG. ACS, REAG. ISO, REAG. PH. EUR.
- ACETONE, 1X1ML, MEOH:WATER(90:10), 5000U G/ML
- ACETONE, A.C.S. REAGENT, >=99.5%
- ACETONE FOR HPLC
- ACETONE CHROMASOLV FOR HPLC >=99.9%
- ACETONE, REAGENTPLUS, >=99%
- ACETONE TECHNICAL, 5 L
- ACETONE CHROMASOLV FOR HIGH-PERFORMANCE LIQUID CHROMATOGRAPHY
- ACETONE DIST. 5 L